Other

All-City replacement bolts and adjustment springs for the Hennepin Bridge and Space Horse dropouts. - Sold as a pair; two bolts and two springs - M4x0.7mm thread - Length: 45mm

Snap-on brake cable guides for bikes that don't have any. - Steel cable housing guide for 1-1/8" top tubes - Snaps on; no bolts - Set of 3 clamps

The All-City Master Dropout is a sliding dropout system consisting of replaceable dropout plates and fixing hardware. Designed for use with 12mm thru-axles and flat-mount brakes, it is compatible only with select All-City models. - Allows riders to convert from a geared to single-speed setup or vice-versa - Compatible only with select All-City models - No additional chain tension adjustment required - Threaded cap / nut for axle installation - Cap nut and O-ring included - Use with drive-side plates

Avid, Post Bracket, Includes Stainless Caliper Mounting Bolts (CPS and Standard)

- Includes stainless steel bolts - 40mm fits 200mm Front and 180mm Rear Rotors

Screws required for mounting Campagnolo hydraulic rear calipers to bicycle frames. Lengths unique to frame specifications.

Compression ring fits above the upper bearing in a Cane Creek headset to ensure vertical and horizontal compression is optimal. - Compatible with 41mm and 42mm OD upper bearings

Crown races for Cane Creek headsets fit a variety of lowers and crown race seat diameters. - Compatible with 10-, 40- and 110-Series headsets and backwards compatible with S and XX Series - Integral mold seals keep out the elements - Compatible with 41 and 42mm lower headset bearings - Compatible with 30mm (1-1/8") straight steerer tubes - Durable steel construction

40-Series replacement cartridge bearings feature durable black oxide construction. - Compatible with 110-, 40-, and 10-Series headsets

40-Series replacement cartridge bearings feature durable black oxide construction. - Compatible with 110-, 40-, and 10-Series headsets

Crown races for Cane Creek headsets fit a variety of lowers and crown race seat diameters. - Compatible with 10-, 40- and 110-Series headsets and backwards compatible with S and XX Series - Integral mold seals keep out the elements

Crown races for Cane Creek headsets fit a variety of lowers and crown race seat diameters. - Compatible with 10-, 40- and 110-Series headsets and backwards compatible with S and XX Series - Integral mold seals keep out the elements - Compatible with 52mm lower headset bearings - Compatible with 30mm (1-1/8") straight steerer tubes - Durable steel construction - Allows the installation of a straight steerer fork without changing out the headset lower

Crown races for Cane Creek headsets fit a variety of lowers and crown race seat diameters. Compatible with 10-, 40- and 110-Series headsets and backwards compatible with S and XX Series - Integral mold seals keep out the elements - Compatible with 52mm lower headset bearings - Compatible with 40mm (1-1/2") tapered steerer tubes - Durable steel construction

Replacement top subassemblies are compatible across Cane Creek 110-, 40-, and 10-Series headsets with the same SHIS values. - Bearings not included - Stack height: 9mm

Replacement top subassemblies are compatible across Cane Creek 110-, 40-, and 10-Series headsets with the same SHIS values. - Bearings not included

40-Series replacement cartridge bearings feature durable black oxide construction. - Compatible with 110-, 40-, and 10-Series headsets

Bearings for Cane Creek AER headsets. - Aluminum Bearing

Replacement top subassemblies are compatible across Cane Creek 110-, 40-, and 10-Series headsets with the same SHIS values. - Bearings not included - Stack height = 9mm

40-Series replacement cartridge bearings feature durable black oxide construction. - Compatible with 110-, 40-, and 10-Series headsets

40-Series replacement cartridge bearings feature durable black oxide construction. - Compatible with 110-, 40-, and 10-Series headsets

These baseplates are the foundation that keeps Chris King headsets turning with legendary smoothness. Manufactured from high-quality stainless steel or titanium, Chris King makes replacement baseplates for all standard sizes and a number of ingenious solutions for those that need something a little special to make their headset work. - Engineered and manufactured in Portland, Oregon USA - High-quality stainless steel and titanium baseplates available for all standard Chris King headset sizes - Titanium baseplates are available in 1-inch and 1 1/8-inch sizes only - Devolution baseplates are a stainless steel solution that allow King headsets to adapt to a wide variety of steerer tube sizes - King Stainless Steel baseplates are available in undersized and oversized versions for irregular steerer tube sizes - 30.0mm ID/40.5mm OD for post-April 1995 1-1/8" Headsets - 30.0mm ID/44.0mm OD for pre- April 1995 1-1/8" Headsets

- Adapts 35mm CenterLock rotor-mount splines to accept an International Standard 6-bolt, 44mm BCD rotor - Does not fit Saint-style 47mm Oversize CenterLock, and will not work with thicker, aluminum-carrier Hope 2005+ style Mono-series rotors - Designed for up to 210mm rotors - Tabs in adapter mate to (6) M5 rotor bolt holes and is secured by CenterLock-style lockring, sandwiching 6-bolt rotor to adapter - Lockring requires a 16-notch external bearing bottom bracket wrench - CL-IS adapter is black and lockring is black with silver etching: 29g

Damper rebuild kit for Topaz model rear shocks.

Simplicity in both form and function is the reason for the CIRCUIT clamp's beauty. We have rounded all of the edges, minimized as much material as possible, and designed a clamp with the perfect touch of refinement and DEITY style. This little gem is the perfect finishing touch for your DEITY kit! - CNC Machined from 6061 T6 aluminum - High-polished ano finish - Minimized design with maximum machining to decrease weight - Super-low stack height for added clearance - Oversized bolt for added clamping power - Lasered DEITY logo and detailing - 31.8mm (22g) - 34.9mm (23g) - 36.4mm (24g)

- Clamps to a threadless steerer, offers up to 3-1/4" stem height increase - Forged 6061 aluminum - Threaded alloy top cap

- Clamps to a threadless steerer - Offers up to 4-1/2" stem height increase - Forged 6061-aluminum provides extra strength - Machined aluminum top cap is threaded, providing easy installation

Dimension Seatpost Clamps - Diameters: 28.6mm, 30.0mm, 31.8mm, 35.0mm - Weight: 34g

Dimension Stem Column Adaptors - Total quill length 180mm - Measurement from minimum insertion to top of steerer adaptor is 118mm - Alloy - Quill insertion diameter: 1-inch

What It Is Replacement hardware for ENVE carbon fiber seatposts. Who It's For Folks who need additional hardware for their ENVE seatposts. Why We Made It We get calls all the time for replacement hardware, so we made a little kit to make it easy for everyone.

- Grade 10 chromium steel balls